EN
TestYourSetup / Mic and audio / Audio latency test

Audio latency test

Measure how long sound takes to get out of your speakers or headphones and back into your microphone. Use it as a Bluetooth latency test, a headphone latency test or a speaker delay check, then line up the lip sync check by eye and ear.

Measure the round trip Measured

Speaker to microphone delay

  1. Use speakers, or hold a headphone ear cup against the mic. With Bluetooth earbuds, hold one earbud right against the computer or phone mic.
  2. Set the system volume to about half and keep the room quiet.
  3. Press Start measuring and allow the microphone. The page plays short clicks and listens for each one.

Echo cancellation, noise suppression and auto gain are switched off, so the mic hears the clicks as they are. Nothing is saved or uploaded.

The microphone is off.

Round trip-ms, median, output + input
Spread-ms, highest minus lowest
Clicks heard-by the microphone

Measured round trip (output + input) and spread, from the audio samples. Below: Estimated numbers reported by the browser, which often leave out Bluetooth and hardware delay.

Output latency-ms, reported by the browser
Base latency-ms, reported by the browser
Mic latency-ms, reported by the browser

The microphone recording around the last click. The blue line is the moment the page sent the click, the orange line the moment the mic heard it. Time in ms.

Press Start measuring to begin.

    Lip sync check Check

    No microphone needed, so it works with Bluetooth headphones on. A ball lands once a second with a tick. Move the slider until the landing and the tick feel exactly together. Try it from both sides, as the point where it feels in sync is wide.

    Press Start check, then move the slider until the ball seems to land exactly on the tick.

    Nothing is uploaded. The microphone only turns on when you press Start measuring, and it turns off when the test ends.

    How this audio latency test works

    The page plays a very short chirp, 8 milliseconds long, through your normal output and records the microphone at the same time. Inside the browser's audio engine a small recorder captures two things side by side, sample for sample: the chirp exactly as the page sent it, and what the microphone picked up. The page then slides the chirp along the recording to find where it matches best (a cross-correlation). The gap between the two is the round trip latency. It is timed in audio samples, about 0.02 ms per step.

    One click can be thrown off by a cough or a busy moment, so the test repeats it 5 to 10 times. It reports the median, which ignores single outliers, and the spread from the lowest to the highest click. A spread of a few milliseconds is normal. A spread of 20 ms or more means the computer was busy, the clicks were faint, or the Bluetooth link was changing its buffer.

    What the result includes

    The measured number is the whole trip: the browser's output buffer, the system mixer and driver, the link to the speaker (USB, HDMI or Bluetooth), the speaker itself, the air between speaker and mic, the microphone, and the input buffer back into the browser. Sound needs about 3 ms per metre of air, so keep the mic close. A browser cannot split this into output and input on its own, because it never hears the speaker without a microphone.

    The output latency, base latency and mic latency boxes come straight from the browser. They are what the browser believes about its own buffers, labelled as reported, not measured. They often leave out the Bluetooth link, TV processing and some driver buffers, which is why the measured round trip is usually larger.

    Typical audio latency

    OutputTypical output delay
    Wired headphones or speakers, built-in sound10 to 40 ms
    USB audio interface with ASIO or a small buffer3 to 10 ms
    HDMI to a TV or soundbar, game mode on20 to 60 ms
    HDMI to a TV, picture processing on80 to 200 ms
    Bluetooth, low latency codec (aptX Low Latency, LE Audio)about 40 to 100 ms
    Bluetooth, standard codecs100 to 300 ms

    These are rough figures for the output only. This test adds the microphone side as well, usually another 5 to 30 ms in a browser, so a wired setup often measures around 20 to 70 ms here. Under about 50 ms, most people do not notice delay in games. Musicians playing live through a computer usually want 10 ms or less.

    Bluetooth latency test: headphones and earbuds

    With Bluetooth headphones on your head, the computer microphone cannot hear the clicks, so the measurement fails. There are two honest ways around it. For a Bluetooth audio latency test with the microphone, take one earbud out, keep the computer or phone mic selected, and hold the earbud right against the mic. For a Bluetooth earphone latency test without a mic, use the lip sync check: it needs only your eyes and ears.

    Do not pick the headset's own mic for this. When any app opens a Bluetooth headset microphone, the headset switches from its music profile to its call profile, with a different codec and a different delay, and the page warns you when that happens. The same switch is why voice chat makes game sound go flat; our mic test explains it.

    The lip sync check

    The ball lands once a second, and the landing is drawn at the moment the browser expects the tick to reach your ears. If your headphones or TV add delay the browser does not know about, the tick comes after the landing. Drag the picture delay slider to the right until both feel exactly together. That value is the extra delay, labelled Check because it depends on your own judgement. People do not notice small offsets, so approach the point from both sides and take the middle. Your screen adds a little delay to the picture too, which slightly reduces the value. Video players and streaming apps correct audio delay automatically, which is why films look fine on Bluetooth while games and rhythm apps feel late.

    How to lower audio latency

    • Go wired for games and music. A cable removes the Bluetooth link, the biggest single delay in most setups.
    • Use a low latency codec. aptX Low Latency and LE Audio (LC3) cut Bluetooth delay a lot, but both the headphones and the computer or phone must support them. A gaming headset with its own USB dongle avoids Bluetooth entirely.
    • Turn on game mode. On TVs and soundbars, game mode skips most picture and sound processing. Many earbuds also have a gaming or low latency mode in their app.
    • Use ASIO or WASAPI exclusive on Windows. Music software and some games can bypass the system mixer with an ASIO driver or WASAPI exclusive mode, and a smaller buffer size (128 or 256 samples) lowers delay further. Raise it again if you hear crackling.
    • Keep the computer free. Close heavy apps and tabs, plug in laptops and turn off battery saver, then run the test again to see the difference.

    Mic latency and speaker delay for calls and streaming

    If you stream or record, the mic side matters as much as the speaker side. Run the test once with your usual mic, then change only one thing, such as the output or a buffer setting, and run it again. The difference between the two medians is the change in delay, because everything else stayed the same. To check a voice against a webcam, record a clip on the camera and mic test while you clap once on camera: if the clap sound comes after your hands meet, add a sync offset to the camera or the mic in your streaming software. For a general latency test of other parts of your setup, try the keyboard latency test, or the ping test for network latency. To check that your speakers play at all and in the right channels, start with the sound test.

    Questions

    How do I test audio latency on my computer?

    Put the microphone near your speakers, set the volume to about half, press Start measuring and allow the microphone. The page plays a series of short clicks, records each one, and measures the time from the moment the click left the page to the moment the mic heard it. The median of all clicks is your round trip latency.

    How do I test headphone latency?

    With wired headphones, hold one ear cup against the microphone and run the measurement. With Bluetooth headphones do the same with one earbud, or use the lip sync check: start it, then move the picture delay slider until the ball lands exactly on the tick. The slider value is the extra delay of your headphones.

    How do I run a Bluetooth earphone latency test?

    Connect the earphones as your normal output, open this page on the computer or phone, and hold one earbud right against the device microphone. Keep the device mic selected, not the earphone mic. Press Start measuring. Standard Bluetooth earphones usually measure about 150 to 300 ms here, low latency modes less.

    What is a good audio latency?

    For the output alone, wired speakers and headphones are usually 10 to 40 ms and Bluetooth 100 to 300 ms. Under about 50 ms most people cannot hear a delay in games or when playing an instrument. Because this test also includes the microphone side, a wired setup often reads around 20 to 70 ms here.

    Why can't the test hear the click with my Bluetooth headphones on?

    The sound goes into your ears, so the computer mic hears almost nothing. Take one earbud out and hold it against the mic, or switch the output to speakers. Also avoid the headset's own mic: opening it switches the headset to call mode, which changes the delay you are trying to measure.

    Why is the measured latency higher than the one my browser reports?

    The browser reports only the parts it knows about, mainly its own output buffer. The measurement is the whole round trip: browser buffer, driver, Bluetooth or HDMI link, speaker, the air, the microphone and the input buffer. Bluetooth delay is often missing from the reported number.

    Does this measure speaker delay or mic latency?

    Both together. A browser cannot time the moment sound leaves a speaker without a microphone, so the result is output plus input. Mic latency is usually the smaller part. To compare speakers or headphones, keep the same mic and change only the output: the difference between two runs is the difference in output delay.

    How do I reduce audio latency for games and music?

    Use wired headphones or speakers, or a low latency Bluetooth codec such as aptX Low Latency or LE Audio. Turn on game mode on TVs and soundbars. In music software use an ASIO driver on Windows, or WASAPI exclusive mode, with a smaller buffer. Close heavy apps, and plug laptops in.

    Is my audio recorded or uploaded?

    No. The page records about one second around each click into memory, measures it and throws it away. Nothing is saved or sent anywhere, and the microphone turns off as soon as the test ends, you press Stop or you leave the tab.

    More tests