How this DPI test works
DPI, more correctly CPI (counts per inch), is how many movement counts your mouse sensor reports for each inch it travels. A mouse at 800 DPI sends 800 counts for one inch of movement. To check mouse DPI you need two numbers: the counts, and the real distance. A web page can read the first but has no idea how far your hand moved, so you give it the distance with something you already own. Every bank card, ID card and driving licence is 85.6 mm long, which makes it a handy ruler.
When you press Start, the page locks the pointer and adds up every count the mouse sends. In Chrome and Edge it asks for unadjusted movement, which hands over the raw sensor counts before Windows pointer speed or acceleration touch them. That is why the result is labelled Measured. The test divides the counts by the inches you entered, rejects a run if your path wandered more than 8% from a straight line, and takes the median of your good runs. If the median is within 7% of a common setting such as 800, 1600 or 3200, it names that setting.
In Firefox and Safari pages only see cursor movement after the system settings, so the result is labelled Estimated. On Windows it is still close if pointer speed is at 10 of 20 and Enhance pointer precision is off. On a Mac it is rough, because macOS always accelerates the pointer.
Why your real DPI differs from the advertised DPI
Do not worry if a mouse set to 1600 reads 1530 or 1690. Sensor deviation of 5 to 10 percent is common, even on expensive gaming mice, and the number can shift with the mouse pad surface, the lift-off distance and dust on the lens. Two copies of the same model can differ. This matters most if you switch mice and want the same feel: measure both and adjust the DPI or in-game sensitivity so they match.
Small errors also come from you. Lining up the start and the end by eye is the biggest one, about 1 mm on each end. Over a card that is roughly 2 percent, over a 30 cm ruler under 1 percent. Three runs and a median keep one sloppy run from spoiling the result, and the spread between runs tells you how far to trust it.
How to check DPI in your mouse software
- Logitech G HUB: select the mouse, open Sensitivity (DPI). The DPI levels are listed and the active one is highlighted. The DPI shift button can change it temporarily.
- Razer Synapse: select the mouse, open Performance. Sensitivity stages show each DPI step; the stage buttons under the wheel cycle through them.
- SteelSeries GG: open Engine, select the mouse and look for CPI. SteelSeries uses CPI, which is the same thing.
- No software: many budget mice only have a DPI button and a light. Measure once after each press to learn the steps, which are often 800, 1200, 1600 and 2400.
Some mice store DPI profiles on board and switch per game, so the number in the app is not always the one in use. A quick test here shows what the mouse is sending right now.
Logitech G305 DPI
The G305 uses Logitech's HERO sensor, which goes from 200 to 12,000 DPI, and the button behind the scroll wheel cycles through its DPI steps. Out of the box the steps are usually 400, 800, 1600 and 3200, and G HUB lets you change them. The mouse has no display of the active step, so after pressing the button, one run here tells you which DPI you are on.
Redragon mouse DPI
Most Redragon mice have a DPI button near the wheel that cycles through preset steps, and many models show the step with a light colour. The steps and colours differ from model to model, and the big number on the box is usually only the highest step. Press the button once, measure, and note the colour next to the result to build your own table. Where a model has Redragon software, you can set the steps there.
Any other mouse
The test reads the counts the sensor sends, so it needs no list of models. It works the same for a Logitech G502, G703 or G Pro X Superlight, a Razer DeathAdder, Basilisk or Viper, a Glorious Model O, a Zowie EC2, and mice from Corsair, HyperX, Roccat, Pulsar, ASUS ROG and Finalmouse. Zowie mice have no software at all, so a measurement here is the only way to confirm the step you are on. This online mouse DPI test is a website, not a program: there is no tool to install, and the site works in any desktop browser.
DPI, sensitivity and eDPI
DPI is set in the mouse. Sensitivity is set in the game and multiplies every count. eDPI is the two multiplied, so 400 DPI at 2.0 and 800 DPI at 1.0 both give 800 eDPI and turn the same in CS2. Because games turn by different amounts per count, eDPI only compares players within the same game. Use cm/360, the distance your mouse travels for one full turn, to compare across games. The calculator above does both from your measured DPI. Moving to another game? The sens converter keeps your cm/360 across 14 shooters, and the aim trainer turns at it.
Changing Windows pointer speed does not change your DPI. It only scales how far the desktop cursor moves per count, after the mouse has sent it. Games that use raw input ignore it, and so does this test in Chrome and Edge.
What DPI should you use for gaming?
Most competitive players sit between 400 and 1600 DPI, with 800 the most common, and set their turn speed in the game. Higher DPI is not more accurate by itself, and at very high settings some sensors add smoothing. A practical approach: pick 800 or 1600, set the desktop pointer speed so the cursor feels right, then tune the in-game sensitivity until a comfortable arm or wrist movement makes a 360. If you came here because aim feels different on a new mouse, measure both mice and match their real DPI, not the advertised one.
Want to check the rest of the mouse? The polling rate test shows how often it reports, and the mouse test checks every button and the wheel.
Questions
How do I check my mouse DPI?
Put a bank card or a ruler on your mouse pad, press Start on this page and slide the mouse exactly the length of the card or the distance you chose, then click. The test divides the counts the sensor reported by the inches you moved. Do it three times and it shows the median and the nearest common setting, such as 800 or 1600 DPI.
Why is my measured DPI different from the number in my mouse software?
Sensors are rarely exact. A mouse set to 1600 DPI often measures between 1500 and 1700, because deviation of 5 to 10 percent is common, and it can change with the mouse pad surface and lift-off distance. Your own runs add a little error too, which is why the test shows the spread between runs.
What is the difference between DPI and CPI?
They mean the same thing for a mouse. CPI (counts per inch) is the correct term: it is how many movement counts the sensor reports for each inch the mouse travels. DPI (dots per inch) comes from printers, but every mouse maker and game uses it, so this page does too.
Does Windows pointer speed change my DPI?
No. DPI is set inside the mouse. Windows pointer speed and Enhance pointer precision change how far the cursor moves for each count, after the mouse has sent it. This test reads the raw counts in Chrome and Edge, so Windows settings do not affect the result there. Most games with raw input ignore them too.
Which browser gives a measured result?
Chrome and Edge on Windows, and other Chromium browsers that support unadjusted pointer lock. They pass the raw sensor counts to the page. Firefox and Safari only give cursor movement after the system settings, so the result there is labelled Estimated and is only fair with Windows pointer speed at 10 of 20 and Enhance pointer precision off.
What is a good DPI for gaming?
Most competitive players use 400 to 1600 DPI, with 800 the most common, and set their turn speed with the in-game sensitivity. Higher DPI is not more accurate in itself. Pick a DPI that lets you move the desktop cursor comfortably, then tune the game with eDPI or cm/360.
What is eDPI?
eDPI is your DPI multiplied by your in-game sensitivity. It lets players compare settings: 800 DPI at sensitivity 1 and 400 DPI at sensitivity 2 both give 800 eDPI in CS2 and turn the same distance. eDPI only compares within one game, because each game turns a different amount per count. Use cm/360 to compare across games.
How accurate is this DPI test?
With raw counts and three careful runs along a bank card, expect about 1 to 3 percent. A longer reference such as a 30 cm ruler or a sheet of A4 paper cuts the error further. Lining up the start and end by eye is the main source of error, so the test shows each run and rejects runs that were not straight.
Can I check DPI without mouse software?
Yes, that is what this test is for. Many office and budget mice have a DPI button but no software and no display of the current setting. Measure once at each press of the DPI button to learn which steps it cycles through.
More tests
Mouse testCheck every button, side buttons and the scroll wheel
Double click testCatch a mouse that double clicks on its own
Polling rate testSee the report rate your browser receives (Hz)
Scroll wheel testFind a wheel that jumps or scrolls backwards
Touchpad testClicks, two finger scroll, pinch and gestures on a laptop touchpad
Keyboard testPress every key, with ISO, AZERTY and QWERTZ layouts