EN
TestYourSetup / Monitor / Touch screen test

Touch screen test

A free touch screen test online for phones, tablets and touch laptops. See every finger with its own number and trail, count how many touches the screen tracks at once, paint the screen to find dead zones, and log ghost touches.

Each finger or pen gets a circle, its number and pointer id, crosshair lines and a trail.
Touching 0 / most 0

Put your fingers on the test area one at a time and drag them around. Each touch gets a number and a trail.

Touching now0touches on the screen
Most at once0simultaneous touches seen
Device reports-touch points, reported by the device
Coverage-of the grid painted
Ghost touches-in the last hands-off check
Pen pressure-pen or stylus only

Touches, coverage and pen pressure Measured Ghost touches Check (only valid if nothing touched the screen)

No permissions needed. Touches are drawn in your browser and nothing is uploaded.

How the touch screen test works

Your phone, tablet or touch laptop has a digitizer: a thin grid of sensors on top of the display that reports where each finger is, many times a second. The browser passes each contact to the page as a pointer with its own id, position and, for a pen, its pressure. This page draws exactly what arrives. If a finger is on the glass and no circle appears under it, the digitizer did not report it.

All three modes use the same test area. It blocks scrolling, pinch zoom and long-press menus, so every touch stays on the canvas. Press Full screen first: the test then covers the whole display, and Esc or the Exit button brings you back. On an iPhone the test fills the browser window, because iOS does not let web pages hide the Safari bars.

Multi touch test: how many fingers does your screen track?

Put one finger down, then add more, spread about a finger width apart. Each touch gets a number in the order it landed, its pointer id from the browser, crosshair lines and a coloured trail. Touching now counts the contacts on the glass this moment; Most at once keeps the highest count, and both are measured. Device reports shows the limit the browser reads from the system (navigator.maxTouchPoints). That number is reported by the device, not tested, so the useful check is whether Most at once reaches it.

If the count stops short, try again with your fingers spread wider. Two fingers pressed together look like one large finger to most digitizers, so they merge into one touch. A trail that breaks up, jumps to another spot or stops while your finger keeps moving is a better sign of a fault than a low count.

Find touch screen dead zones by painting the grid

Switch to Dead zones, go full screen and swipe over every cell. A cell turns green as soon as the screen reports a touch inside it, and the page fills the gaps between two reports so a fast swipe still paints a solid line. Coverage shows the painted share of the grid. At 80% the empty cells turn red, so the last ones are easy to find. Swipe slowly over each red cell a few times. A cell that stays red while the cells around it fill is a dead zone: that part of the digitizer does not respond.

Dead zones often follow a line, for example a dead strip across the keyboard area, because the sensor grid is wired in rows and columns. Use the small cells to look for small spots. One caution: the outer edge of many phones belongs to the system for back swipes and the home bar, so a thin strip right at the edge that never paints is not always a fault. Test the edge again with the phone turned sideways before you blame the screen.

Ghost touch test

Ghost touches are touches the screen reports when nobody is touching it. Pick a listening time and press Start ghost touch check. The page goes full screen and counts down three seconds so you can put the device down. While it listens, every touch or pen press is logged with the time and position, and marked in red on the screen.

Be clear about what this can and cannot tell you. A browser sees a ghost touch and a real finger in exactly the same way, so the page cannot tell them apart. The result is only meaningful if nothing touched the screen: no hands, no sleeve, no flip case lid, no water drops. If touches appear under those conditions, they came from the hardware. Where the browser shares it, the result also says whether the device was charging, because a faulty charger is a common trigger.

Touch screen not working properly? What to try

  1. Clean and dry the screen. Water drops, grease and dust confuse the sensor and cause both ghost touches and missed touches.
  2. Remove the screen protector and case. Air bubbles, dirt under a protector or a tight case pressing on the edges are the most common cause of dead spots and ghost touches. Test again without them.
  3. Unplug the charger. If ghost touches only appear while charging, try the original charger and cable. Electrical noise from a poor charger reaches the digitizer.
  4. Restart the device and install system updates. Touch firmware and drivers get fixes in updates, and a restart clears a stuck touch controller.
  5. Check the system settings. On Android, Settings, Display often has a touch sensitivity or glove mode option; on a touch laptop, make sure the touch screen is enabled in Device Manager on Windows.
  6. Repair. A dead zone that never paints after these steps, or ghost touches with nothing on the screen, point to a faulty digitizer or display assembly. Note the positions from this test for the repair shop or warranty claim.

Pen and stylus check

Draw with a stylus and the circle grows with pressure. The Pen pressure box shows the value from 0 to 1 that the browser receives, with the tilt in degrees. A pen that reports a constant pressure, or 0 while drawing, either does not support pressure in the browser or is being treated as a finger. Fingers do not report real pressure on most screens, so the box only fills for a pen.

Other screen checks

Touch and display are separate layers. If you see lines, dark spots or coloured dots, run the dead pixel test. To see how smoothly the screen updates, try the refresh rate test. For a laptop touchpad rather than a touch screen, use the touchpad test.

Questions

How do I test my touch screen?

Open this page on the phone, tablet or touch laptop and press Full screen. In Multi touch, put your fingers down one at a time and drag them around: each touch gets a circle, a number and a trail. Then switch to Dead zones and paint the whole grid with a finger. Cells that never turn green after you swipe right over them are spots that do not respond.

How do I do a multi touch test?

Use the Multi touch mode and add fingers one by one, spread apart. The Touching now number shows how many touches the screen reports at this moment, and Most at once keeps the highest count. Compare it with the number your device reports. Fingers held very close together can merge into one touch, so keep them a finger width apart.

How many touch points does my phone support?

The Device reports box shows navigator.maxTouchPoints, the number the browser says the touch screen supports. It is reported by the device, not measured. Most at once is the measured number: how many touches this page actually saw at the same time. Many Android phones report 5 or 10.

How do I find a dead zone on my touch screen?

Use Dead zones in full screen and swipe across every cell. Once 80% is painted, the empty cells turn red so they are easy to find. Swipe slowly over a red cell several times. If it stays red while the cells around it fill, that spot does not register touch. Small cells find smaller spots.

What is ghost touch and how do I check for it?

Ghost touch is when the screen reports touches that nobody made: apps open on their own, the keyboard types, or the page scrolls. Choose Ghost touch, press Start, put the device down and keep your hands off. The page logs every touch it receives. It cannot tell a real finger from a ghost touch, so the result only means something if nothing touched the screen.

Why does my phone screen touch by itself?

The common causes are a cheap or faulty charger (ghost touches that only happen while charging), a screen protector with dust or bubbles under it, moisture, a cracked digitizer, heat, or a bent frame pressing on the display. Remove the case and protector, unplug the charger and run the ghost touch check again to narrow it down.

Can I test pen pressure here?

Yes, when your browser passes pen data on. Draw with a stylus such as an Apple Pencil or an S Pen and the Pen pressure box shows the pressure from 0 to 1, with the tilt angles. The circle grows with pressure. Fingers do not report pressure on most screens, so this box stays empty for touch.

Does this touch screen test work on iPhone?

Yes. Safari on iPhone and iPad sends every finger to the page, and the test area blocks scrolling and zooming. iPhones do not let web pages go truly full screen, so the test fills the browser window instead. The bottom bar and the home indicator area belong to iOS, so test the very bottom edge with the phone turned sideways as well.

Is this a digitizer test?

Yes. The digitizer is the touch sensing layer on top of the display, and every result here comes from it: the number of touches, where they land and whether some spots stay silent. A display fault (lines, dead pixels, colours) is a different part; check that with the dead pixel test.

More tests