How this UFO test works
The page asks the browser to draw once per screen refresh and times every frame. From those times it measures your refresh rate, shown as Measured, and counts the frames the browser missed. Each UFO then moves by the same number of pixels on every frame: the speed in px/s divided by your refresh rate. At 960 px/s that is 16 px per frame at 60 Hz and 6.7 px at 144 Hz.
The top lane updates on every frame. The second lane updates every second frame, the third every fourth, and so on, so all lanes travel at the same speed but at 1/1, 1/2, 1/4 and 1/8 of your frame rate. That lets you compare 144 fps, 72 fps and 36 fps side by side on one monitor. Everything you judge here is labelled Check, because only your eyes can see the pixels change.
This is only as good as the browser's timing. If the measured rate does not match your monitor, or the dropped frames count keeps climbing, the UFOs will stutter for reasons that have nothing to do with the panel. Fix that first, using the notes under the test.
What you are seeing
- Blur trail. On normal LCD and OLED screens each frame stays lit until the next one, while your eyes keep moving. The UFO smears by about one frame step, which is the Step per frame figure. Double the refresh rate and the smear halves. This is motion blur, and every sample-and-hold screen has it.
- Ghosting. A faint second copy or a dark tail behind the UFO, separate from the smear. It comes from pixels that change colour too slowly. It shows most on the grey background.
- Inverse ghosting or overshoot. A bright or coloured halo, often a light edge behind a dark object. The monitor's overdrive is pushing pixels too hard.
- Stutter. The UFO jumps or hitches instead of gliding. That is uneven frame delivery: dropped frames, a busy computer, or a browser running at a rate that does not match the display.
- Lower lanes. At 1/4 and 1/8 of the rate the UFO visibly steps along. That is what low fps looks like even on a fast monitor, and it is why a high refresh rate only helps when the game can keep up.
Ghosting test for your monitor, step by step
- Set Test to UFO lanes, Speed to 960 px/s and Background to Grey. Grey shows both dark and bright trails.
- Follow the top UFO with your eyes and look at its edges, especially the trailing one.
- Open the monitor menu and change the overdrive or response time setting one step at a time. Names vary: Overdrive, Response Time, Trace Free, AMA.
- Keep the setting where the trail is shortest without a bright halo. On many monitors that is the middle setting; the fastest one usually overshoots.
- Repeat on the Light and Dark backgrounds. Some panels, especially VA, smear on dark scenes much more than on bright ones.
If your monitor has a backlight strobing mode, often called motion blur reduction, turn it on and compare. The blur trail should shrink sharply. Strobing usually needs a fixed refresh rate and may turn off variable refresh rate (G-Sync or FreeSync), and some people notice flicker. VRR itself does not change this test much: a browser window normally runs at the fixed maximum rate.
Motion blur test with a camera
Your eyes are a good judge, but a photo makes results easy to compare. Choose Pursuit camera. The strip carries a checkerboard, a comb of thin lines and the UFO, all moving together. Set the phone to manual or pro mode with a shutter of about 1/30 s, then slide the phone sideways at the strip's speed as you take the photo; a ruler or table edge helps keep it level. Take several shots at 480 px/s first, since slower is easier to follow. In the sharpest photo the stationary grey ticks above the strip are smeared, and the blur at the checkerboard edges is the motion blur your eyes see.
Frame skipping test
An overclocked monitor, or one fed an odd timing by the graphics card, can accept a high refresh rate yet silently drop frames. The browser cannot see that, because the frames leave the computer on time. Choose Frame skipping and photograph the screen with a shutter of about 1/10 second or slower. Each refresh lights the next numbered cell, so the photo should show a run of lit cells with no gaps. A dark cell inside the run means the monitor skipped a frame. A cell that is much brighter than the rest means a frame was shown twice, usually because the browser dropped a frame; the dropped frames count under the test tells you which.
If the measured rate is wrong
Turn on hardware acceleration (in Chrome and Edge, Settings, System, Use graphics acceleration when available), set the full refresh rate in your display settings, plug a laptop into power and turn off battery saver. With two monitors, move this window to the fast one. The refresh rate test has a full checklist for a screen stuck at 60 Hz.
More monitor tests
Check for stuck pixels with the dead pixel test, look for PWM and VRR flicker with the monitor flicker test, and film how long a click takes to reach the screen with the input lag test.
Questions
What is a UFO test?
A UFO test moves a small UFO across the screen at a fixed speed so you can judge motion clarity: how sharp a moving object looks, whether it leaves a trail (ghosting) and whether motion is smooth. Several lanes run the same UFO at the full refresh rate and at half and quarter rates, so you can see what more frames per second buy you.
How do I test my monitor for ghosting?
Pick the UFO lanes, a speed of 960 px/s and the grey background, then look at the top lane. A faint copy or smear behind the UFO is ghosting. A bright or dark halo, often with a coloured edge, is overshoot from too much overdrive. Try each overdrive setting in the monitor menu and keep the one with the cleanest edge.
What is inverse ghosting?
Inverse ghosting, also called overshoot or coronas, is a bright or coloured outline trailing a moving object. It happens when the monitor pushes pixels too hard to speed them up. The fix is a lower overdrive or response time setting in the monitor on-screen menu.
Is motion blur the same as ghosting?
No. Ghosting is a separate faint copy caused by slow pixel transitions. Motion blur is the even smear you see on any sample-and-hold screen because each frame stays lit while your eyes keep moving. Blur shrinks with a higher refresh rate or with backlight strobing; ghosting shrinks with the right overdrive setting.
Why does the UFO stutter?
Stutter means frames are arriving unevenly. Check the dropped frames count under the test. Close heavy tabs and apps, plug in a laptop, and make sure the measured Hz matches your monitor. A browser on a second screen sometimes runs at the main screen's rate, which also causes stutter.
Why does the UFO test show 60 Hz on my 144 Hz monitor?
The monitor may be set to 60 Hz in Windows or macOS, the cable or port may not carry more, or browser hardware acceleration is off. Set the rate in your display settings, use DisplayPort or HDMI 2.0 or newer, turn on hardware acceleration in the browser and reload this page.
How do I test for frame skipping?
Choose Frame skipping, then photograph the screen with a shutter of about 1/10 second or slower. Each frame lights the next numbered cell, so the photo should show an unbroken run of lit cells. A dark gap in the run is a skipped frame, which is common on overclocked monitors.
Does backlight strobing reduce motion blur?
Yes, a lot. Modes often called motion blur reduction or ULMB flash the backlight once per frame, so each frame is shown for a shorter time and the smear shrinks. The image gets dimmer, and many monitors only allow strobing at a fixed refresh rate with variable refresh turned off.
More tests
Black screenA full black screen, one click
White screenA full white screen, one click
Refresh rate testYour monitor Hz, measured in the browser
What is my screen resolutionScreen resolution, browser window size and pixel ratio
Monitor size calculatorScreen size in inches, PPI and aspect ratio