How to use the gyroscope test
- Open this page on the phone or tablet you want to test and tap Start sensors. On an iPhone or iPad, Safari asks for motion and orientation access: tap Allow.
- Turn the device left and right, then tip it forward and back. The orientation angles, the rotation rate and the chart should all move smoothly, and the drawing of the phone should follow.
- Lay it flat. The bubble should settle near the middle, acceleration with gravity should show about 9.8 on z (-9.8 on an iPhone, which reports the opposite sign), and the rotation rate should drop close to 0.
- Run the still check for the drift and noise numbers.
On a desktop or most laptops you will see "No motion sensor found". That is the honest answer: those machines have no gyroscope or accelerometer to report.
What each reading means
A phone sensor test is really several tests in one, because a phone has several motion sensors, and the browser shows them in two groups. All values here are measured: they are exactly what the browser receives.
- Orientation (alpha, beta, gamma), degrees. The device's angles, worked out by the system from the gyroscope, accelerometer and often the magnetometer. Beta is front to back tilt, gamma is left to right tilt, and alpha is the turn around the vertical axis. This is the tilt test most people want.
- Rotation rate, degrees per second. The raw gyroscope: how fast the device is turning around each axis right now. It reads near 0 when the device is still, whatever angle it is held at.
- Acceleration with gravity, m/s². The raw accelerometer. Gravity is always in it, so a still device shows about 9.81 m/s² in total, split across the axes by how it is held.
- Acceleration without gravity, m/s². Only the movement you add, with gravity removed by the system. It needs a gyroscope, so phones without one often leave it empty.
The update rate shows how many motion events reach the page per second. Many phones deliver around 60, and browsers may slow it down when the battery is low or the tab is in the background.
The still check: drift and noise
A good gyroscope reads almost exactly 0 when nothing moves. The still check records 5 seconds with the device flat on a table and estimates three things. Gyro bias is the average rotation rate while still: a large bias makes game aiming, AR views and 360 degree videos slowly turn on their own. Gyro noise is how much the reading jitters around that average. Heading drift is how far alpha turns per minute while the device lies still. The accelerometer side reports the average total, which should be close to 9.81 m/s², and its noise.
These results are labelled Estimated for good reasons: 5 seconds is short, a washing machine or a passing truck can shake the table, and browsers round the values slightly. If the check says the device moved, try again on a heavier, steadier surface.
Tilt from flat mixes two things the page cannot separate: how level your table is and any offset in the sensor. To tell them apart, use the flip method. Run the check, turn the device 180 degrees on the same spot and run it again. If the tilt changes, the table is sloped. If it stays about the same, the sensor itself has an offset.
Gyroscope not working? What to try
- Allow motion access. On iPhone, tap Start sensors and Allow. In Chrome on Android, tap the icon left of the address bar, then Site settings, Motion sensors, Allow.
- Restart the phone. A sensor service that has stopped often comes back after a restart.
- Calibrate. Lay the phone flat and still for a few seconds, and for the compass move it in a figure 8. Some Android phones have a sensor test in their service menu, and many games have their own gyro calibration.
- Remove magnets. Magnetic cases, car mounts and wallet cases upset the compass and, through it, the alpha angle.
- Check for a gyroscope. If Gyroscope says Not found after Start, your phone may only have an accelerometer. No setting can add a missing sensor.
Compass heading
A compass heading appears only when the browser gives the page a real one. Safari on iPhone and iPad provides a compass heading from the magnetometer, with an accuracy figure. Chrome on Android provides absolute orientation, which this page turns into a heading when the device is held flat. Other browsers give only relative angles, where alpha starts from wherever the device was when the page began, so the page does not pretend that is north. Keep it flat and away from metal, and treat it as a quick check rather than a navigation tool.
Controller gyro
This page reads the motion sensors of the device it runs on. A game controller is different: the standard gamepad interface that browsers use for controllers has buttons and sticks but no motion sensors, so a DualSense, DualShock or Switch controller gyro cannot be read through it. The PS5 controller test can show DualSense motion data through WebHID in Chrome or Edge on a computer, and the controller test checks the buttons and sticks of any pad. For a phone or tablet screen, try the touch screen test.
Questions
How do I test the gyroscope on my phone?
Open this page on the phone and tap Start sensors (allow motion access on iPhone). Turn the phone in each direction: the rotation rate numbers and the chart should move smoothly and return to near zero when you stop. Then lay the phone flat and run the still check to see how much the gyroscope reads while nothing moves.
How do I test the accelerometer?
Start the sensors and lay the phone flat. Acceleration with gravity should show about 9.8 m/s² on the z axis (iPhones show -9.8, because Safari uses the opposite sign) and close to 0 on x and y, and the total should read about 9.81 m/s² in any position while the phone is still. Tilt it on its side and the 9.8 should move to the x or y axis.
Why does it say no motion sensor found?
Your browser is not getting any motion data. Desktop computers and most laptops have no motion sensor at all. On a phone, check that motion access is allowed: on iPhone, tap Start and allow it; in Chrome on Android, tap the icon left of the address, open Site settings and allow Motion sensors.
Why does iPhone ask for permission?
Since iOS 13, Safari only shares motion and orientation data after you allow it, and the request has to come from a tap. That is why nothing runs until you press Start sensors. If you tapped Deny, close the tab and open the page again; if it still fails, clear this site in Settings, Apps, Safari, Advanced, Website Data.
How do I know if my phone has a gyroscope?
After you press Start, the Sensors found box says whether rotation rate data arrives. Some low cost phones have only an accelerometer. They can still detect tilt, but not smooth rotation, so 360 degree videos, AR apps and gyro aiming in games work poorly or not at all.
Is the compass heading accurate?
It is the heading your device reports, and it is only shown when the browser provides one: the compass heading on iPhone, or absolute orientation in Chrome on Android. Hold the phone flat, away from magnets, cases with magnets, laptops and metal. Do not use it for navigation. If it drifts, calibrate the compass by moving the phone in a figure 8.
Can I test my controller gyro here?
Not on this page. Browsers do not give web pages a controller's motion sensors through the standard gamepad interface, so a DualSense or Switch controller gyro is invisible to it. The PS5 controller test can read DualSense motion data through WebHID in Chrome or Edge on a computer.
What do alpha, beta and gamma mean?
They are the three orientation angles in degrees. Alpha is the turn around the vertical axis, like a compass (0 to 360). Beta is the front to back tilt (-180 to 180), and gamma is the left to right tilt (-90 to 90). Lying flat face up, beta and gamma are both close to 0.
More tests
Online compassDigital compass on your phone, with true north for your location
Bubble levelSpirit level on your phone: surface and edge, degrees and percent slope
Vibration testMake your phone vibrate: patterns to test the vibration motor (Android)
Mouse testCheck every button, side buttons and the scroll wheel
Keyboard testPress every key, with ISO, AZERTY and QWERTZ layouts
Controller testButtons, sticks, triggers and vibration for any gamepad