EN
TestYourSetup / Aim and sensitivity / Valorant to Marvel Rivals sens

Valorant to Marvel Rivals sens

Your Marvel Rivals sensitivity is about your Valorant sensitivity times 4 at the same DPI. Type yours below for the value, cm/360 and eDPI.

From
To
Your Marvel Rivals mouse sensitivity Approximate1.4Marvel Rivals = Valorant x 4
cm/36046.7same in both games
in/36018.4inches per full turn
eDPI before280Valorant, DPI x sens
eDPI after1,120Marvel Rivals, DPI x sens

Train at this sens

Valorant

Horizontal FOV is fixed at 103 degrees. Scoped sensitivity multiplier is a separate setting and is not converted here.

Turn rate: 0.07 degrees per count at 1. Source: 0.07 degrees per count is the widely reproduced 360 measurement; it gives the well-known ratio CS2 = Valorant x 3.18 (0.07 / 0.022).

Marvel Rivals

Third-person camera with a wide default FOV, so the same cm/360 can feel slower than a first-person game. Some heroes have scoped or zoomed abilities with their own sensitivity.

Turn rate: 0.0175 degrees per count at 1. Source: A guide states Marvel Rivals = Valorant x 4 at the same DPI, which means 0.0175 degrees per count. Only one public source, so it is marked approximate.

Hip fire at the same cm/360 (360 degree distance). Scoped and ADS sensitivity are separate settings in most games and are not converted here.

No permissions needed. Everything runs in your browser and nothing is uploaded.

Multiply by 4, approximately

Valorant turns 0.07 degrees per mouse count at sensitivity 1. For Marvel Rivals the commonly published rule is that its sensitivity is four times your Valorant number at the same DPI, which means about 0.0175 degrees per count. So Marvel Rivals sens = Valorant sens x 4: Valorant 0.35 at 800 DPI is 46.7 cm for a full turn, and so is Marvel Rivals 1.40.

We mark Marvel Rivals as approximate. The developer has not published the figure and we found only one public source for the ratio, so a small error is possible. If something feels off, measure your real cm/360 in the practice range and use the cm/360 calculator to work back to the right number.

Common Valorant sens values in Marvel Rivals

Valorant sensMarvel Rivals senscm/360 at 400 DPIcm/360 at 800 DPIcm/360 at 1600 DPI
0.20.8163.381.640.8
0.251130.665.332.7
0.31.2108.954.427.2
0.351.493.346.723.3
0.41.681.640.820.4
0.451.872.636.318.1
0.5265.332.716.3
0.62.454.427.213.6
0.83.240.820.410.2

Same DPI in both games. Calculated from the turn rates in the sens converter table; one of these games is marked approximate, so check with a 360 test.

Tactical shooter to hero shooter

Valorant is about holding an angle and clicking once. Marvel Rivals is a third-person hero shooter where targets fly, swing and dash, fights last longer and many heroes track rather than flick. The camera sits behind your hero, so a 90 degree turn shows a different slice of the world than the same turn in Valorant. That is why a matched cm/360 often feels slow at first.

A sensible path: start at the converted value for your main hitscan hero, play a few games, then raise it in 5 to 10 percent steps if you lose track of fast targets. Practise with the aim trainer Tracking mode at your new value; it turns at the same cm/360 you set here.

Going from Marvel Rivals back to Valorant, press Swap in the converter. For any other pair use the main sens converter.

Questions

How do I convert Valorant sens to Marvel Rivals?

Multiply your Valorant sensitivity by 4 at the same DPI. Valorant 0.35 becomes about 1.40 in Marvel Rivals. The converter above also gives your cm/360 and eDPI.

How sure is the Marvel Rivals number?

Less sure than Valorant or CS2. NetEase has not published the turn rate, and the x4 ratio comes from a public guide rather than a documented measurement, so this page marks it approximate. A 360 test in the practice range is the way to confirm it: turn once and measure the mouse travel, then compare with the cm/360 shown here.

Why does Marvel Rivals feel slower at the same cm/360?

It is a third-person game with a wide view, so the same turn moves the picture across the screen differently, and many heroes fly, dash or swing, which means bigger and faster camera moves than in Valorant. Many players raise their sensitivity a little after a few games. Start converted, then adjust in small steps.

Should I use the same sens for every hero?

If you use hero-specific settings, your converted Valorant sens is a good base for hitscan heroes. Heroes that track a lot or move fast may suit a higher value; heroes with scopes have their own zoom settings.

What else should I check before converting?

Turn off any mouse acceleration, in the game and Windows Enhance pointer precision, so the same movement always turns the same amount. Your DPI is what carries over between games, so check it with the DPI test if you are not sure what your mouse really sends.

More tests